KQ MiniSynth – Miscellaneous modules

KQ MiniSynthAll modules

I/O Panel

This is a fixed panel for Input/Output.

Connectors / Parameters

  • Volume

    Change Volume.

  • Pan

    Change Pan position.
    64 — Center.

  • Portamento Time

    Change time during gliding notes.
    0 — Do not glide.
    100 — 1 seconds.
    127 — 20 seconds.

  • RESET button

    Reset all controllers.

  • GLIDE button

    Enable always gliding.

  • Gate/Velo

    This outputs the strength with which you press a key.
    The range is -1 ~ 1:
    0 ~ 1 if keys are pressed, -1 if not.

  • V/Oct

    This outputs the pitch of the key.

  • Mod

    This outputs the value of the modulation wheel.
    The range is -1 ~ 1.

  • Start/Stop

    This outputs the state of the button “START”/”STOP”.

  • Tempo

    Set how fast it beats.
    Also you can set Tempo with tapping the button “TAP”.

  • Speaker Output

    The synthesizer outputs this input as sound.

  • PANIC button

    Silence if in panic.

KQ MiniSynthAll modules

Custom Controller

Dummy Panel

Output MIDI Controller Value.
Use this module if you control the Synth with MIDI signal.
Also it is able to change the value.

Connectors/Parameters

  • Ctrl No

    MIDI Control Number.
    LSB controllers are valid though those are not selectable.

  • Value

    A value of the controller.

  • Fine button

    If enabled, the value range is 0 ~ 127.
    If disabled, the range is -8192 ~ 8191.

  • Value Out

    Output the value.
    This outputs -1.0 if the fine value is -8192,
    0 if the value is 0,
    1.0 if the value is 8191, or so on.

KQ MiniSynthAll modules

Const Value

This outputs a constant value.

Connectors / Parameters

  • Coarse

    Set a coarse value.

  • Fine

    Set a fine value.

  • Value

    Displays the value.

  • V/Oct

    Displays a note name when the value is treated as V/Oct.

  • Out

    The output.

KQ MiniSynthAll modules

8 Step CV Sequencer

Synchronized with tempo, loops 1~8, and outputs the CV value.
You can set the CV value of each step.
The duration per 1 step is constant.

Connectors / Parameters

  • 1…8

    Set the CV value of each step.

  • 1 Step Duration

    The duration per 1 step.

  • Transition Time

    Changes the output smoothly during this duration when stepping forward.
    The output changes immediately when this value is 0.

  • Sequence Length

    The loop does the appointed step.

  • Start/Stop

    This module runs when this input is on.

  • Pause

    This module pauses during this input is on.

  • CV Out

    The output.

KQ MiniSynthAll modules

8 Step Gate Sequencer

Synchronized with tempo, loops 1~8, and outputs -1 (off) or 1 (on).
You can set the duration, during which the output is on, of each steps.
The duration per 1 step is constant.

Connectors / Parameters

  • 1…8

    Set the duration during which the output is on.

  • 1 Step Duration

    The duration per 1 step.

  • Sequence Length

    The loop does the appointed step.

  • Start/Stop

    This module runs when this input is on.

  • Pause

    This module pauses during this input is on.

  • Gate Out

    The output.

KQ MiniSynthAll modules

Loop Gate (Tempo Sync)

This outputs -1 or 1 with syncronizing the Tempo.
You can turn on/off gate at fixed timing.
The sequence is Before → Active → After → Before.
The output is 1 when the state is “Active”, -1 when the others.

Connectors / Parameters

  • Before / Active / After

    Each represents the duration of the state.

  • Duration

    The overall duration.

  • Start/Stop

    This module runs when this input is on.

  • Out

    The output.

KQ MiniSynthAll modules

Dummy Panel

Dummy Panel

This is a blank panel.

KQ MiniSynthAll modules